For years my wife and I had agreed that we would one day leave Oklahoma for someplace we really loved. That day finally arrived last year when we found a home in Vancouver, Washington that met our dreams. Only thing missing was someplace for a woodshop. Well, there was a place, under a deck, but not a room. So, as part of the move we had a local contractor build a room that would one day be the wood shop. Fortunately there was already a door from the house into this area, and about half of the “walls” were there, in the form of concrete retaining walls.
My advice here is to make a detailed list of what the various parts of the build will be (drawings, permits, foundation, framing, electrical, etc.) and decide what you would like to do yourself and what you will need to hire others to do. Get quotes on the work that you would like to hire out and estimate the materials you will need to do your portion. You may want to factor in your time into the cost as well, especially if you will be passing up other income to work on the project. At some lumberyards, you will be able to give detailed drawings to an estimator on staff who will do a material takeoff list for you of what you’ll need and what it will cost. When all the numbers come in, you can put together a budget and plan for an overrun allowance of around 15 percent. If you keep track of the materials and subcontract costs as you go, you can stay on track and make decisions as you go about the latter stages of the project without regretting it later. If it is challenging to obtain funding for a complete build, you may want to stage the build so that initially the frame goes up and the exterior is finished, and then you finish the interior work as you have time or as funds become available.
Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
The primary investment of any garage workshop are the tools. Protect your investment with a high quality tool chest that is neatly organized and (if needed) lockable. Look for smooth rolling ball-bearing drawers, and if you’re buying used, beware of rust and dirt that could corrode your tools. We recommend installing drawer mats to keep your tools from sliding around. They also give your tools a softer cushion to rest in.
When we published our massive review on how much an app costs back in 2015, we had no idea it would become the top resource on the web. Two years later, that piece is still considered the definitive resource for app development costs in our industry. It’s because of its popularity that I feel compelled to revisit this subject. Additionally, doing so will allow for some fresh perspectives based on what's changed in the app industry as well as another way to look at the topic.
Hello! My name is Donna Jean. I love to read books and my job is to write a daily review of all the novelties in the world of eBooks. I allow only the best of them to be published on my website. I really hope to make our world more bright, beautiful and kind. You can participate by downloading any book from my site, and you will receive health, luck, kindness, and love, which will support you during all your life. Wishing your dreams begin to come true, and every tomorrow be happy for you. Thank you! ❤❤❤
We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.
If you’re moving into a space that requires renovations in order to fit your business needs, you’ll also want the landlord to take on responsibility for that work. We’re not talking aesthetics here, we mean necessary renovations such as improved data connectivity. If you have to do the work yourself, it’s advisable to ask the landlord for a rent-free or reduced-rent period. You should also make sure that any additional alterations you have in mind are acceptable and would not be in breach of the lease. Last but not least, always make sure the do’s and don’t of what can and cannot be done is put in writing, it will save you a lot of headaches later.
Both of those broader lenses are still useful ways to look at app costs, but costs can additionally be broken down by app type and the features associated with them. Also, two years in technology is a very long time. So, we will start by looking at what's changed. We'll then move on to looking at app costs based on the different kinds of apps in the market.
A commercial real estate lease is a long-term rental agreement between the landlord of a commercial space and a business. There are many types of commercial leases and many types of commercial spaces. Leases include full service leases, net leases, and modified gross leases. These leases help tenants rent out office spaces, retail and restaurant locations, as well as industrial spaces.
After years of digging through piles of stuff on my workbench for the air compressor accessory I needed, I had this idea. I simply drilled 7/16- in. holes on the underside of my workbench top and threaded in a few 1/4-in. NPT male couplings with quick-connect couplers. A wrench and some upward pressure are all it took to screw the couplings into the wood. Now I just snap my accessories onto the couplers when I’m not using them. — Donnie Dressler. These are the best tools for automotive work.
After looking at a number of spaces that are available to lease, you may start to wonder whether it’s better to buy or lease commercial real estate. Of course, there are occasions when it might be better to purchase commercial real estate rather than leasing it. For example, if you buy a commercial space, you’ll take advantage of equity, depreciation, cash flow, and asset appreciation.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
People tend to buy cargo vans for work and hold on to them for years, so many vans on the market can be pretty beat up. Although you can find inexpensive cargo vans in good condition, it can be tough to find anything with lower mileage - so be prepared for all that comes with owning a higher mileage vehicle. Cargo vans also don’t offer much headroom. There’s no way even shorter people will be able to stand in one, and the lack of headroom also cuts down on storage space.
I like how you thought out the lighting for you shop. I have 6ea.6 tube T-8s but find 6500K bulbs but find lighting for filming is not that good, seems dark to me I use a Canon T3i its a decent camera I do have a row of windows in a 16′ garage door and aman door with a window on one end and a small window at the other end of my shop. Any idea what the issue may be?Could I still be getting too much light?
SBA provides support and tools to aspiring small business owners and in particular to minority-owned, women-owned, disadvantaged, and veteran-owned businesses, including a government-backed financing scheme to qualified participants. Local and state authorities also have a range of programs designed to encourage the growth of your small business. Make sure to research your local authority’s website.
At the very least get the basics of shop design right with great lighting, clean displays, and a well thought out layout. Once you have all of this pulled together you can add a dose of your own personality to the store's design to break through the noise and establish a connection with your target customers. The goal is to be memorable and maximize sales per square foot at the same time!
Hi Ryan: Nice job on the truck. I also have ’94 Toya 4×4 coffin sleep setup. Looking to change (access cab wanted) and may use some of your ideas. One thing I didn’t see you mention is ventilation. I am from the Mid-Atlantic region(DC/Maryland, you’re old stomping grounds) and ventilation at the New is important. My side windows have screens and I use an old mesh fly with a flexible pole for the rear tailgate area. It works really well. Kinda jerry rigged but is easy to put up and take down as well as pass through for nighttime truck exits. Not needed out west as much since bugs and humidity are lower but can’t live w/out it in these parts.
If your shop will be attached to your house or another structure, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
The core criteria of small business site selection will always be foot traffic and ease of access. In places like New York City, this means being by the subway or on a busy street. But for most of America it’s about considering traffic flow and parking accessibility. Ever see three gas stations at the same intersection? They are all picking off different traffic flows because they know customers are looking for the shortest possible detour.
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
If you are looking to sell your business, it is important to engage a lawyer who is a business specialist to ensure you gain the best possible valuation. A small business is valued by assessing the potential ongoing income from the business over the coming few years. Normally this means that a business will be valued at three to five times net revenues, which can present a potential issue for particularly tax-savvy small business owners. Remember that every time you write off an expense against your business, you are lowering the net margin of the business. So, that dollar you saved by writing off the expense could cost you three to five dollars on the valuation of your business.
Check your local papers, especially the free shoppers, for information about upcoming shows Another venue for craft retailing is at the local flea markets that spring up in every community just about every weekend. Again the entrance cost is usually minimal. Ultimate Small Shop Result The only other thing you need is a little marketing savvy. With little cost and some effort, you will be well on your way to knowing whether there is a market for your craft. Once you know that, you can move on and think about other ways of selling, such as in galleries, on consignment, on eBay or from your own website. Once you spend your precious time and energy creating a scrapbook, make sure it lasts! There are a few simple things you can easily do to ensure that your scrapbooks look just as good as the day you finished them, for years to come. The first thing to avoid is paper that is not lignin-free. You’ve probably heard that before, and it is true, but what is lignin anyways? Lignin is a stiff component of a plant that quite literally holds it together. Although lignin is necessary for plants and trees, you want nothing to do with it! After a while, lignin will cause photos, fabrics and other paper that touch it to turn brown. Yes, the lignin-free paper does cost more, but it is a vital part of preserving your cherished scrapbooks. If the paper is not lignin-free, it will eventually discolor your photos and other materials touching it. So when buying paper for your scrapbooking projects, be sure to look for packages that say “lignin-free,” because if it doesn’t say it, then it most likely isn’t.The fabric is a big concern for preserving your scrapbooks, but unfortunately, it is often overlooked. Many people assume that all fabrics are acid-free, but they aren’t. Silk actually goes through an acid bath during the manufacturing process, as well as many tie-dyed fabrics. This isn’t to discourage you from using it, not all. Just try to make sure that no photos directly touch fabric, and if you need them to overlap, make sure there is a layer of paper between the two. Another consideration when using fabrics is if the color will bleed off onto your page and other things touching it. To test for this, cut a square inch off and soak it in a glass of water overnight. If there is no color bleeding from it the next day, then there isn’t any risk to your scrapbook. But if you do see color in the water, or collecting at the bottom of the glass then don’t use that fabric in your scrapbook at all. When using glitter, be sure there is a top layer of spray adhesive to lock them down, or better yet use special glitter glue where the glitter is mixed right in. If this is not done right the glitter will slowly fall off, and loose glitter means scratched photos. After you have planned the layout for your photos, be sure that you are using the right kind of mounting tape for them! Regular mounting tape is fine for buttons and bottle caps, but when it comes to mounting photos you need to use special photo mounting tape which is completely acid-free. Ultimate Small Shop Member If you don’t, your photos will slowly discolor. The tape should say “acid-free” right on the packaging.
If you are just getting started in woodworking and want to know what tools you’ll need to set up shop, you’ll want to download this free PDF from Popular Woodworking. We have put together a complete list of basic woodworking tools to kick-start your new hobby. In this free download, you’ll get our recommendations for the best hand and power tools for beginners. Buy these tools and you’ll have everything you need to make great woodworking projects.
I used to keep screws in a cof- fee can, but when I reached in with my hand, the screw points pricked my fingers. The can was also a dust and dirt depot. I bought a clear water bottle with a pop-up lid and poured screws into the bottle with a funnel. The screws stay clean, and I can shake them out of the bottle one at a time. — Bruce Burley. Hardware Storage: DIY Tips and Hints
I have a plastic bed lining on my truck, which also covered the back of the tailgate… I just popped the screws off, took off the plastic liner and drilled holes in the sheet of plywood to match those used by the plastic tailgate cover. Sorry if that doesn’t help you with your setup. But I’m sure you could just drill your own holes in the metal tailgate. Use the plywood cover as a guide for your screw holes…
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
While we were painting all of the walls in our workshop our plumber dropped by to hook up an old laundry tub sink that we’ve had for several years. Now, he hooked up to the cold water line on an outside water faucet, so we’ll only have cold water but still this will be really convenient to have this right here in this shop. Well we’re about to set our last base cabinet, and once they secure that well to the wall we can start on all of our countertops.
I’m a 60 year young widow who just bought a bright yellow 2003 S10 step side with the intention of camping in it. But I discovered that finding a used S10 step side topper is harder than finding hen’s teeth!! Buying a new one wasn’t an option. Just found a black step side topper for a Ford Ranger. Isn’t a perfect fit but it works. And the colors compliment each other although color wasn’t my primary concern. I took two days to drive from the St. Louis area of MO to the Kansas City area to pick it up.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
The beauty of a portable A/C unit is that you don’t have to heft it into a window and block off a valuable source of fresh air for keeping paint fumes at bay. Instead, choose a model with a low profile that you can tuck under a table or against a wall when not in use — a model with casters for maximum maneuverability is ideal. Choose a high-powered unit that will condition at least 400 square feet of space and move it where you need it for maximum comfort as you work.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
When leasing a retail space, there is always risks involved. Your goal should be to minimize these as much as possible by considering every angle and asking the right questions. For example, does the landlord intend on erecting scaffolding on the building at any point during the lease? If so, can the rent be reduced to reflect this situation? You will also want to ask to have a clause included allowing you to sublet if necessary, which can be important if you ever find yourself struggling to make payments.
Are your table saw accessories where you need them—when you need them? Follow reader D. E. Warner’s advice: Attach pegboard panels to the stand to hold the wandering herd of push sticks, blades, throat plates, wrenches and jigs. On an open metal stand with angle-iron legs, drill holes in the legs and bolt the pegboard in place. Here’s another super storage project using pegboard.
The threshold area, also known as the "decompression zone," is the very first space that prospective customers step into when they enter your store. It typically consists of the first five to fifteen feet worth of space, depending on the overall size of your store. It's also the space where your customers make the transition from the outside world and first experience what you have to offer.
Really enjoyed watching the video of the shop build. You will be turning out great pieces in no time. At the end of the video it looks like you have your dust collection system up and running. Where did you purchase the duct work? I thought I remember you talking about this in the old shop. Did you use regular HVAC 4″ round duct or a heavier piece. Thanks for the insight and good woodworking.