In addition, if your aisles aren’t wide enough, you could be subject to complaints or lawsuits under the Americans with Disabilities Act (ADA). The ADA requires you to have aisles that are at minimum three feet wide. If you’re reported to be non-compliant, you could be fined if you don’t widen your aisles and remove obstructions. Learn more about the ADA’s retail store requirements here.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.

You can see I broke the ultimate goal down into smaller tasks. Now you just need to do this for all the big goals that you have mapped out for the year. You may have more ideas or goals throughout the year and that’s okay. With this type of document, you are able to add another category and tasks anytime you want. This is just the best way to keep track of all the little things you need to do to accomplish your goals so you never are stuck wondering what you have to do next.


As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
It’s no accident that some of the best marketers in the tech startup industry are known as “growth hackers.” Think about your target demographic (e.g. students, local mothers, teenagers) and find any way you can to get the word out to them. Email mommy bloggers, hand out free samples at the local college, or write your website on all the napkins you hand out with your food. There is no substitute for action.
I have a question, you mention what a problem it would be if the cinder blocks were to sink yet you have installed them with the least amount of footprint on the ground. Was there a reason for this? I would have installed them with the flat side on the ground, and I realize they would not hold as much load as the way you have them but considering the number you have used, the spacing, and the size of the shed, load should not be a problem. Just wondering.
Now that you have your goals mapped out and you know the exact tasks that will help you accomplish them, I want you to pick a day of the week (preferably Monday or Friday) and start planning the week ahead - don’t skip this step, never skip this step. Schedule which one these tasks will happen on what day of the week. So you are literally pulling the tasks from that spreadsheet and placing them into this weekly planner. It’s important to keep in mind deadlines (the ones you set for your goals and when they should be accomplished) and the amount of time it takes you to do a task. You may also want to write down which day it’s due, and who is responsible for this task (if you work with a team).

Next up are the chisels, you can start with a couple of sizes and build from there. When looking at saws, for joinery a dovetail saw is a good place to start, with a choice between western style or Japanese. For precise cuts across the grain, cutting tenon shoulders, and defining the edges of a dado a carcass saw also makes a good complement to the dovetail saw.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
Meaghan Brophy is a retail writer for Fit Small Business. She has provided content and guidance for indie retailers for years as the editor for Independent Retailer magazine, a RetailWire BrainTrust panelist, and speaker at trade shows such as the Independent Retailer Conference and NY NOW. She has been quoted as a retail expert in Forbes, Retail Dive, Retail Minded, ASD Insider, and more. When not talking retail, Meaghan can be found watching dog videos and practicing her tap dancing skills.
Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!

At times, while you are starting a small business, it will seem like there is a brick wall in front of you, made up of all the different problems that will occupy your time and mind: a lack of funds, permits, regulations, tax worries, inventory issues, or a lack of customers. Concepts like “free time” and “the weekend” will take on a very different meaning. While the emotional ups and downs of cash flow management and customer service, may drain your will to live.


Once I had the walls completely filled in and trimmed out, I built my doors.  I clamped them in place each day until after I painted.  Then I installed the hinges and hardware.  I decided to change my original plan of building a hinged 4 foot door.  I was worried that the weight of it would cause it to sag over time.  I had also decided at this point to install a small unused AC in the back wall.  I thought that by keeping one of the doors closed, I could keep more cold air in during the hot summers.
as the name implies--I have no qualms about using castoffs, trash or clearanced items in my shop--I have a 3and one half car garage that I can't get a vehicle in(even tho I like to change my own oil, etc.) because I have so many interests like woodworking, metalworking, plastics, machining, machine building, carpentry, etc. we have to store our kids furniture somewhere, as well as some of our own... You involve a welder, 2 tablesaws, bandsaw, planer, lathe, drillpress, benches and benchtop tools--not to mention storage of materials and I've got a collosal mess that I may never get straightened out!!!--Did I mention room for the woodburning stove I heat it with??? I am always appreciative of these "dream shops" I see in FineWoodworking"
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
Ideally, the stands should lift the speakers to roughly ear level of a sitting person. This is important because it aligns the ​subwoofers and tweeters relative to the ear and achieves the best balance of sound. The high frequencies are often missed when speakers are placed too high or too low. Speakers placed on a shelf or table often cause the surface to vibrate, thus distorting bass. These speaker stands isolate the speaker's vibrations from the floor, allowing you to hear the bass from the speaker and not the vibrations from a shelf, table or floor. Speakers come in various sizes and shapes, so the height of your speaker stands is dependent on your unique speakers. For this project, we give you the dimensions suited for the speakers shown in the photo, but you can alter the design to fit your individual needs.
One of the most heavily used tools in your shop will be your table saw.  It is absolutely essential for ripping stock to size, working with composite material (like plywood and MDF), and venturing into the world of wood working jigs.  Budget is a limiting factor in a $500 build, but at $150 it is hard to pass up adding this Craftsman saw to your shop - even with limited funds.  

Ordinary clip-in-place shelf brackets with slotted metal supports can hold a lot of weight. But some-times they’re unstable and can be easily knocked loose. The play in the slots allows the bracket and shelf to shift from side to side. To prevent this, use your circular saw to cut 1/8-in. deep slots into the undersides of the shelves, aligned with each bracket. When the shelf is assembled, the brackets fit into the slots, eliminating the sway. Also check out: How To Build Floating Shelves.
If you’ve spent time at your local flea or farmers’ market over the last few years, you may have noticed the explosion that has taken place in the number of innovative small business concepts. From cool new clothing lines to ingenious fusion foods, the sheer diversity of the ideas on display really hammers home one of the key lessons when starting a small business: You need to find your key differentiator. For some this is their brand story, for others it’s the value of their service, but for many quick service restaurants and small retailers, it’s a distinctive core product line that demands the attention and interest of your customers.
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself). woodworking shop design
×